Section
15 - General Products, Chemical Specialties, and End Use Products
Volume 15.01, January 2005
Refractories, Activated
Carbon; Advanced Ceramics
C0016-03 Test Method for Load Testing
Refractory Shapes at High Temperatures
C0020-00 Test Methods for Apparent Porosity,
Water Absorption, Apparent Specific Gravity, and Bulk Density of Burned
Refractory Brick and Shapes by Boiling Water
C0024-01 Test Method for Pyrometric Cone
Equivalent (PCE) of Fireclay and High Alumina Refractory Materials
C0027-98R02 Classification of Fireclay and
High-Alumina Refractory Brick
C0071-01A Terminology Relating to
Refractories
C0092-95R99 Test Methods for Sieve Analysis
and Water Content of Refractory Materials
C0108-46R04 Symbols for Heat Transmission
C0113-02 Test Method for Reheat Change of
Refractory Brick
C0133-97R03 Test Methods for Cold Crushing
Strength and Modulus of Rupture of Refractories
C0134-95R99 Test Methods for Size,
Dimensional Measurements, and Bulk Density of Refractory Brick and Insulating
Firebrick
C0135-96R03 Test Method for True Specific
Gravity of Refractory Materials by Water Immersion
C0155-97R02 Classification of Insulating
Firebrick
C0179-04 Test Method for Drying and Firing
Linear Change of Refractory Plastic and Ramming Mix Specimens
C0181-03 Test Method for Workability Index of
Fireclay and High-Alumina Plastic Refractories
C0182-88R04 Test Method for Thermal
Conductivity of Insulating Firebrick
C0198-02 Test Method for Cold Bonding
Strength of Refractory Mortar
C0199-84R00 Test Method for Pier Test for
Refractory Mortars
C0201-93R04 Test Method for Thermal
Conductivity of Refractories
C0202-93R04 Test Method for Thermal
Conductivity of Refractory Brick
C0210-95R99 Test Method for Reheat Change of
Insulating Firebrick
C0288-87R02 Test Method for Disintegration of
Refractories in an Atmosphere of Carbon Monoxide
C0357-94R02E01 Test Method for Bulk Density
of Granular Refractory Materials
C0401-91R00 Classification of Alumina and
Alumina-Silicate Castable Refractories
C0416-97R02 Classification of Silica
Refractory Brick
C0417-93R98 Test Method for Thermal
Conductivity of Unfired Monolithic Refractories
C0454-83R02 Practice for Disintegration of
Carbon Refractories by Alkali
C0455-97R99 Classification of Chrome Brick,
Chrome-Magnesia Brick, Magnesia-Chrome Brick, and Magnesia Brick
C0456-93R03 Test Method for Hydration
Resistance of Basic Bricks and Shapes
C0467-97R02 Classification of Mullite
Refractories
C0492-92R03 Test Method for Hydration of
Granular Dead-Burned Refractory Dolomite
C0544-03 Test Method for Hydration of Dead
Burned Magnesite or Periclase Grain
C0545-97R02 Classification of Zircon
Refractories
C0577-99 Test Method for Permeability of
Refractories
C0583-00 Test Method for Modulus of Rupture
of Refractory Materials at Elevated Temperatures
C0604-02 Test Method for True Specific
Gravity of Refractory Materials by Gas-Comparison Pycnometer
C0607-88R00 Practice for Coking Large Shapes
of Carbon-Bearing Materials
C0621-84R01 Test Method for Isothermal
Corrosion Resistance of Refractories to Molten Glass
C0673-97R03 Classification of Fireclay and
High-Alumina Plastic Refractories and Ramming Mixes
C0704-01 Test Method for Abrasion Resistance
of Refractory Materials at Room Temperature
C0767-93R04 Test Method for Thermal
Conductivity of Carbon Refractories
C0768 Practice for Drip Slag Testing
Refractory Materials at High Temperature
C0830-00 Test Methods for Apparent Porosity,
Liquid Absorption, Apparent Specific Gravity, and Bulk Density of Refractory
Shapes by Vacuum Pressure
C0831-98R03 Test Methods for Residual Carbon,
Apparent Residual Carbon, and Apparent Carbon Yield in Coked Carbon-Containing
Brick and Shapes
C0832-00 Test Method of Measuring the Thermal
Expansion and Creep of Refractories Under Load
C0860-00 Practice for Determining the
Consistency of Refractory Castable Using the Ball-In-Hand Test
C0861-93R00 Practice for Determining Metric
Dimensions of Standard Series Refractory Brick and Shapes
C0862-02 Practice for Preparing Refractory
Concrete Specimens by Casting
C0863-00 Test Method for Evaluating Oxidation
Resistance of Silicon Carbide Refractories at Elevated Temperatures
C0865-02 Practice for Firing Refractory
Concrete Specimens
C0874-99R04 Practice for Rotary Slag Testing
of Refractory Materials
C0885-87R02 Test Method for Young's Modulus
of Refractory Shapes by Sonic Resonance
C0899-79R02 Practice for Use of Metric Units
of Measure for Reporting Properties of Refractory Materials
C0903-98R04 Practice for Preparing Refractory
Castable Specimens by Cold Gunning
C0909-93R00 Practice for Dimensions of a
Modular Series of Refractory Brick and Shapes
C0914-95R04 Test Method for Bulk Density and
Volume of Solid Refractories by Wax Immersion
C0973-87R98 Practice for Preparing Test
Specimens From Basic Refractory Gunning Products by Pressing
C0974-87R98 Practice for Preparing Test
Specimens from Basic Refractory Castable Products by Casting
C0975-87R98 Practice for Preparing Test
Specimens from Basic Refractory Ramming Products by Pressing
C0987-00A Practice for Vapor Attack on
Refractories for Furnace Superstructures
C1054-03 Practice for Pressing and Drying
Refractory Plastic and Ramming Mix Specimens
C1099-92R02 Test Method for Modulus of
Rupture of Carbon-Containing Refractory Materials at Elevated Temperatures
C1100-88R98 Test Method for Ribbon Thermal
Shock Testing of Refractory Materials
C1113-99R04 Test Method for Thermal Conductivity
of Refractories by Hot Wire (Platinum Resistance Thermometer Technique)
C1145-03 Terminology of Advanced Ceramics
C1161-02C Test Method for Flexural Strength
of Advanced Ceramics at Ambient Temperature
C1171-96R03 Test Method for Quantitatively
Measuring the Effect of Thermal Shock and Thermal Cycling on Refractories
C1175-99AR04 Guide to Test Methods and
Standards for Nondestructive Testing of Advanced Ceramics
C1190-95R00 Practice for Location of Test
Specimens from Magnesia-Carbon and Impregnated Burned Basic Brick
C1198-01 Test Method for Dynamic Young's
Modulus, Shear Modulus, and Poisson's Ratio for Advanced Ceramics by Sonic
Resonance
C1211-02 Test Method for Flexural Strength of
Advanced Ceramics at Elevated Temperatures
C1212-98R04 Practice for Fabricating Ceramic
Reference Specimens Containing Seeded Voids
C1223-92R03 Test Method for Testing of Glass
Exudation from AZS Fusion-Cast Refractories
C1239-00 Practice for Reporting Uniaxial
Strength Data and Estimating Weibull Distribution Parameters for Advanced
Ceramics
C1259-01 Test Method for Dynamic Young's
Modulus, Shear Modulus, and Poisson's Ratio for Advanced Ceramics by Impulse
Excitation of Vibration
C1273-95AR00 Test Method for Tensile Strength
of Monolithic Advanced Ceramics at Ambient Temperatures
C1274-00 Test Method for Advanced Ceramic
Specific Surface Area by Physical Adsorption
C1275-00 Test Method for Monotonic Tensile
Behavior of Continuous Fiber-Reinforced Advanced Ceramics with Solid
Rectangular Cross-Section Test Specimens at Ambient Temperature
C1276-94R99 Test Method for Measuring the
Viscosity of Mold Powders Above Their Melting Point Using a Rotational
Viscometer
C1282-00 Test Method for Determining the
Particle Size Distribution of Advanced Ceramics by Centrifugal
Photosedimentation
C1286 Classification for Advanced Ceramics
C1291-00A Test Method for Elevated
Temperature Tensile Creep Strain, Creep Strain Rate, and Creep Time-to-Failure
for Advanced Monolithic Ceramics
C1292-00 Test Method for Shear Strength of
Continuous Fiber-Reinforced Advanced Ceramics at Ambient Temperatures
C1322-02A Practice for Fractography and
Characterization of Fracture Origins in Advanced Ceramics
C1323-96R01 Test Method for Ultimate Strength
of Advanced Ceramics with Diametrally Compressed C-Ring Specimens at Ambient
Temperature
C1326-03 Test Method for Knoop Indentation
Hardness of Advanced Ceramics
C1327-03 Test Method for Vickers Indentation
Hardness of Advanced Ceramics
C1331-01 Test Method for Measuring Ultrasonic
Velocity in Advanced Ceramics with Broadband Pulse-Echo Cross-Correlation
Method
C1332-01 Test Method for Measurement of
Ultrasonic Attenuation Coefficients of Advanced Ceramics by Pulse-Echo Contact
Technique
C1336-96R02 Practice for Fabricating
Non-Oxide Ceramic Reference Specimens Containing Seeded Inclusions
C1337-96R00 Test Method for Creep and Creep
Rupture of Continuous Fiber-Reinforced Ceramic Composites under Tensile Loading
at Elevated Temperatures
C1341-00 Test Method for Flexural Properties
of Continuous Fiber-Reinforced Advanced Ceramic Composites
C1358-96R00 Test Method for Monotonic
Compressive Strength Testing of Continuous Fiber-Reinforced Advanced Ceramics
with Solid Rectangular Cross-Section Specimens at Ambient Temperatures
C1359-96R00 Test Method for Monotonic Tensile
Strength Testing of Continuous Fiber-Reinforced Advanced Ceramics With Solid
Rectangular Cross-
Section Specimens at Elevated Temperatures
C1360-01 Practice for Constant-Amplitude,
Axial, Tension-Tension Cyclic Fatigue of Continuous Fiber-Reinforced Advanced
Ceramics at Ambient Temperatures
C1361-01 Practice for Constant-Amplitude,
Axial, Tension-Tension Cyclic Fatigue of Advanced Ceramics at Ambient
Temperatures
C1366-04 Test Method for Tensile Strength of
Monolithic Advanced Ceramics at Elevated Temperatures
C1368-01 Test Method for Determination of
Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress-Rate
Flexural Testing at Ambient Temperature
C1407-98 Practice for Calculating Areas,
Volume, and Linear Change of Refractory Shapes
C1419-99A Test Method for Sonic Velocity in
Refractory Materials at Room Temperature and Its Use in Obtaining an
Approximate Young's Modulus
C1421-01B Test Methods for Determination of
Fracture Toughness of Advanced Ceramics at Ambient Temperature
C1424-04 Test Method for Monotonic
Compressive Strength of Advanced Ceramics at Ambient Temperature
C1425-99 Test Method for Interlaminar Shear
Strength of 1\ND and 2\ND Continuous Fiber-Reinforced Advanced Ceramics at
Elevated Temperatures
C1444-00 Test Method for Measuring the Angle
of Repose of Free-Flowing Mold Powders
C1445-99 Test Method for Measuring
Consistency of Castable Refractory Using a Flow Table
C1446-99 Test Method for Measuring
Consistency and Working Time of Self-Flowing Castable Refractories
C1465-00 Test Method for Determination of
Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress-Rate
Flexural Testing at Elevated Temperatures
C1468-00 Test Method for Transthickness
Tensile Strength of Continuous Fiber-Reinforced Advanced Ceramics at Ambient
Temperature
C1469-00 Test Method for Shear Strength of
Joints of Advanced Ceramics at Ambient Temperature
C1470-00 Guide for Testing the Thermal
Properties of Advanced Ceramics
C1494-01 Test Methods for Determination of
Mass Fraction of Carbon, Nitrogen, and Oxygen in Silicon Nitride Powder
C1495-01 Test Method for Effect of Surface
Grinding on Flexure Strength of Advanced Ceramics
C1499-04 Test Method for Monotonic
Equibiaxial Flexural Strength of Advanced Ceramics at Ambient Temperature
C1525-04 Test Method for Determination of
Thermal Shock Resistance for Advanced Ceramics by Water Quenching
C1547-02 Classification for Fusion-Cast
Refractory Blocks and Shapes
C1548-02 Test Method for Dynamic Young's
Modulus, Shear Modulus, and Poisson's Ratio of Refractory Materials by Impulse
Excitation of Vibration
C1557-03E01 Test Method for Tensile Strength
and Young's Modulus of Fibers
D2652-94R99 Terminology Relating to Activated
Carbon
D2854-96R04 Test Method for Apparent Density
of Activated Carbon
D2862-97R04 Test Method for Particle Size
Distribution of Granular Activated Carbon
D2866-94R04 Test Method for Total Ash Content
of Activated Carbon
D2867-04 Test Methods for Moisture in
Activated Carbon
D3379-75R89E01 Test Method for Tensile
Strength and Young's Modulus for High-Modulus Single-Filament Materials
D3466-76R98 Test Method for Ignition
Temperature of Granular Activated Carbon
D3467-04 Test Method for Carbon Tetrachloride
Activity of Activated Carbon
D3802-79R99 Test Method for Ball-Pan Hardness
of Activated Carbon
D3803-91R04 Test Method for Nuclear-Grade
Activated Carbon
D3838-80R99 Test Method for pH of Activated
Carbon
D3860-98R03 Practice for Determination of
Adsorptive Capacity of Activated Carbon by Aqueous Phase Isotherm Technique
D4069-95R03 Specification for Impregnated
Activated Carbon Used to Remove Gaseous Radio-Iodines from Gas Streams
D4607-94R99 Test Method for Determination of
Iodine Number of Activated Carbon
D5029-98R04 Test Method for Water Solubles in
Activated Carbon
D5158-98 Test Method for Determination of the
Particle Size of Powdered Activated Carbon by Air Jet Sieving
D5159-04 Guide for Dusting Attrition of
Granular Activated Carbon
D5160-95R03 Guide for Gas-Phase Adsorption
Testing of Activated Carbon
D5228-92R00 Test Method for Determination of
the Butane Working Capacity of Activated Carbon
D5742-95R00 Test Method for Determination of
the Butane Activity of Activated Carbon
D5832-98R03 Test Method for Volatile Matter
Content of Activated Carbon Samples
D5919-96R01 Practice for Determination of
Adsorptive Capacity of Activated Carbon by a Micro-Isotherm Technique for
Adsorbates at ppb Concentrations
D6385-99 Test Method for Determining Acid
Extractable Content in Activated Carbon by Ashing
D6586-03 Practice for the Prediction of
Contaminant Adsorption On GAC In Aqueous Systems Using Rapid Small-Scale Column
Tests
D6646-03 Test Method for Determination of the
Accelerated Hydrogen Sulfide Breakthrough Capacity of Granular and Pelletized
Activated Carbon
D6647-01 Test Method for Determination of
Acid Soluble Iron Via Atomic Absorption
D6781-02 Guide for Carbon Reactivation
D6851-02 Test Method for Determination of
Contact pH with Activated Carbon
No comments:
Post a Comment